1.  gunzip apache_xxx.tar.gz
2.  tar -xvf apache_xxx.tar
3.  gunzip php-xxx.tar.gz
4.  tar -xvf php-xxx.tar
5.  cd apache_xxx
6.  ./configure --prefix=/www --enable-module=so
7.  make
8.  make install
9.  cd ../php-xxx

10. Now, configure your PHP.  This is where you customize your PHP
    with various options, like which extensions will be enabled.  Do a
    ./configure --help for a list of available options.  In our example
    we'll do a simple configure with Apache 1 and MySQL support.  Your
    path to apxs may differ from our example.

      ./configure --with-mysql --with-apxs=/www/bin/apxs

11. make
12. make install

    If you decide to change your configure options after installation,
    you only need to repeat the last three steps. You only need to 
    restart apache for the new module to take effect. A recompile of
    Apache is not needed.
  
    Note that unless told otherwise, 'make install' will also install PEAR,
    various PHP tools such as phpize, install the PHP CLI, and more.

13. Setup your php.ini file:

      cp php.ini-dist /usr/local/lib/php.ini

    You may edit your .ini file to set PHP options.  If you prefer your
    php.ini in another location, use --with-config-file-path=/some/path in
    step 10. 
    
    If you instead choose php.ini-recommended, be certain to read the list
    of changes within, as they affect how PHP behaves.

14. Edit your httpd.conf to load the PHP module.  The path on the right hand
    side of the LoadModule statement must point to the path of the PHP
    module on your system.  The make install from above may have already
    added this for you, but be sure to check.
        
    For PHP 4:
            
      LoadModule php4_module libexec/libphp4.so

    For PHP 5:
                      
      LoadModule php5_module libexec/libphp5.so
      
15. And in the AddModule section of httpd.conf, somewhere under the
    ClearModuleList, add this:
    
    For PHP 4:
    
      AddModule mod_php4.c
      
    For PHP 5:
    
      AddModule mod_php5.c

16. Tell Apache to parse certain extensions as PHP.  For example,
    let's have Apache parse the .php extension as PHP.  You could
    have any extension(s) parse as PHP by simply adding more, with
    each separated by a space.  We'll add .phtml to demonstrate.

      AddType application/x-httpd-php .php .phtml

    It's also common to setup the .phps extension to show highlighted PHP
    source, this can be done with:
    
      AddType application/x-httpd-php-source .phps

17. Use your normal procedure for starting the Apache server. (You must
    stop and restart the server, not just cause the server to reload by
    using a HUP or USR1 signal.)

1.  gunzip -c apache_1.3.x.tar.gz | tar xf -
2.  cd apache_1.3.x
3.  ./configure
4.  cd ..

5.  gunzip -c php-5.x.y.tar.gz | tar xf -
6.  cd php-5.x.y
7.  ./configure --with-mysql --with-apache=../apache_1.3.x
8.  make
9.  make install

10. cd ../apache_1.3.x

11. ./configure --prefix=/www --activate-module=src/modules/php5/libphp5.a
    (The above line is correct! Yes, we know libphp5.a does not exist at this
    stage. It isn't supposed to. It will be created.)

12. make
    (you should now have an httpd binary which you can copy to your Apache bin dir if
    it is your first install then you need to "make install" as well)

13. cd ../php-5.x.y
14. cp php.ini-dist /usr/local/lib/php.ini

15. You can edit /usr/local/lib/php.ini file to set PHP options.
    Edit your httpd.conf or srm.conf file and add:
    AddType application/x-httpd-php .php

1. Several Linux and SysV variants:
/etc/rc.d/init.d/httpd restart

2. Using apachectl scripts:
/path/to/apachectl stop
/path/to/apachectl start

3. httpdctl and httpsdctl (Using OpenSSL), similar to apachectl:
/path/to/httpsdctl stop
/path/to/httpsdctl start

4. Using mod_ssl, or another SSL server, you may want to manually
stop and start:
/path/to/apachectl stop
/path/to/apachectl startssl